Acoustic guitar nut slot height

acoustic guitar nut slot height

  • Guitar Maintenance: Check Action at the Nut | Acoustic Guitar
  • Proper Guitar Nut Height And Action
  • Adjusting the Nut Slots: Guitar Setup and Maintenance (Video) - Musicians Institute - Nashville
  • Pack the slot bottom with baking soda, clean away the excess, and then apply thin superglue.

    Guitar Maintenance: Check Action at the Nut | Acoustic Guitar

    Use a toothpick to apply the superglue until the baking soda looks wet, being careful not to get any on the peghead. For best results, let the fill cure overnight. Try to keep the slots spaced evenly and angled down so the fuitar point is where it meets the fingerboard.

    acoustic guitar nut slot height

    Select a file that best fits the fret, and file the fret down a small amount. Then tune back up, and use the feeler gauge to check the distance once more.

    Proper Guitar Nut Height And Action

    It may seem easy, and it is, but only if you take your time and allow yourself to relax and approach the project at a reasonable pace. In the end, it is all up to you. Make your adjustments, and if you feel a bit nervous, bring your guitar to a professional. Good luck, and be careful; your guitar is yeight as good as you treat it.

    Within the 3 full-length DVDs you receive, you will learn everything from correctly restringing your guitar to adjusting actionschecking relief and more….

    Adjusting the Nut Slots: Guitar Setup and Maintenance (Video) - Musicians Institute - Nashville

    Click here to cancel reply. If Unsure, Engage a Professional to Do the Job If you have any reservations about performing this adjustment yourself, it is best that you save up a little bit of cash on the side and get the job done professionally, as a bad case of nerves can cause you to make a mistake.


    Steps to Get the Nut Height Filed Correctly In order to make adjustments to the action of the nut, you will need a set of files, one that coincides with the width of each string rut in the nut, a feeler gauge, a tuner, and some time and a whole lot of patience. The ideal nut slot height, in terms of playability, is subjective — much like string action height at the bridge.

    Some players like the slots to be cut up a little higher like slide playersand some players want them cut down as sslot as possible so the guitar plays very easy with dlot fight. You can measure the nut slot heights by placing a feeler gauge in between the bottom of the string and the top of the first fret when the guitar is up to pitch and after the neck and bridge are adjusted.

    Steps to Get the Nut Height Filed Correctly. In order to make adjustments to the action of the nut, you will need a set of files, one that coincides with the width of each string rut in the nut, a feeler gauge, a tuner, and some time and a whole lot of patience. The first thing you want to do is take your feeler gauge and check the distance. Jan 16,  · The correct nut height is the same as the frets. With that in mind, action over the first fret depends on the saddle height. With the correct nut height, action at the first fret should be about 12% of the action at the 12th fret. In other words, unless you like a 12th fret action of 1/4", then " at the first fret is way too high. Mar 16,  · The ideal nut slot height, in terms of playability, is subjective — much like string action height at the bridge. Some players like the slots to be cut up a little higher (like slide players), and some players want them cut down as low as possible so the guitar plays very easy with no ideass.coted Reading Time: 6 mins.

    This is why you use a capo at the first fret in all previous steps — to take the nut slot heights out of the equation, saving them for last. You can start this process by making sure the guitar is up to pitch. Then read the nut slot depths. As a starting point, shoot for. On ehight guitars with a wound G, you will also shoot for.

    acoustic guitar nut slot height

    The feeler gauge should be placed on top of the first fret, sliding underneath each string. If there is extra space, then the slot is cut too high and will need to come down until the string lightly touches the top of the gauge.

    If the gauge pushes the string up, then the slot will need to be filled and re-cut to raise the slot. You can fill and re-cut a nut slot by wicking either bone dust or the rolled-up fibers of a Q-tip in the slot with thin Cyanoacrylate glue. Using a super glue accelerator to instantly toughen the material, trim the excess, and then re-cut the slot.

    2 thoughts on “Acoustic guitar nut slot height”

    1. Billy Leyba:

      Have you ever had issues fretting a note closer to the nut? If you have either of these issues, chances are your nut action height is off, and this can lead to your strings coming out of tune. How does this happen?

    2. Donna Garcia:

      After adjusting the truss rod and setting the string saddle heights at the bridge, you can now make the third adjustment, which is to the nut slots. There are three aspects of the nut slots that you will be addressing in the setup process in order to make sure that they are cut correctly:.

    Add a comments

    Your e-mail will not be published. Required fields are marked *